Technical Inspection & Vehicle Safety Requirements

  • Modifications – Any modification to a vehicle must meet a standard of safety in design and installation.
  • Lug Nuts – All lug nuts must be torqued to the Vehicle’s Specs and on approved fasteners, and be used on every stud. Lug nuts must have a minimum of 5 to 7 turns worth of thread.
  • Hub spacer/ adapter – Hub spacers or adapters must be installed properly and torqued to specifications. Lug nuts used in conjunction with these adapters must retain minimum threading to hold tension and be present on every stud.
  • Wheels / Tires – All drivers must have 2 spare mounted tires that are not used on the course to drive home or load vehicle on trailer. Aftermarket wheels and tires must not rub against the fender of the vehicle where its going to damage a Tire or interfere with Steering.
  • Engine – Modifications to the engine must not interfere with required safety systems (brakes, steering, etc) of the vehicle. Engine modifications must also not create a fire or fluid leakage hazard. All aftermarket piping must be properly secured to the frame of the vehicle. Vehicles with transplanted engines must have all intake channels, intercooler piping (if present), and exhaust piping properly secured to the vehicle.
  • Suspension – No Blown / saggy Suspension, No Missing Bushings If present, aftermarket suspension arms, alignment compensation brackets, and steering linkages must be torqued to specifications and meet required tensile strength.
  • Brakes – Brake systems must be able to handle extended periods of hard driving conditions. Brakes must be properly bled and all seals in good condition, pedal and linkages must be free of excessive wear, play and malfunction or missing parts. Brake pads must have more than 25% of original condition. Master cylinder and calipers must be within specification. Brakes must be free of fluid leaks.
  • Body / Suspension – The body of a vehicle must be able to adequately protect the driver, No Structural Rust, No Body Parts or Panels loose ect.
  • Steering System – Steering system and linkages must be in proper working order with no leaks.
  • Windows / Windshields – Windows and windshields must be free of cracks or breaks that impair drivers vision or safety.
  • Battery – The battery must be secured by a standard battery bracket, and at least the positive terminal covered by proper electrical insulation.
  • Air Cleaner – The intake air cleaner system must be adequately secured to the frame of the vehicle with proper fasteners.
  • Oils and Fluids – All necessary fluids such as engine oil, transmission oil, brake fluid, and other important engine fluids must be filled to manufacturer specifications. Leaks of any of these fluids are not permissible.
  • Throttle – The throttle action must be smooth and the throttle spring must be to specification.
  • Ignition / Fuel System – The fuel system of the vehicle must be responding properly and free of any leakages. Any wiring or tubing associated with the fuel delivery or ignition system must be clear of hot areas to prevent potential fire hazards.
  • Wiring Harness – Any insulation associated with the wiring harness must not present a potential fire hazard (i.e. clear of hot areas of the engine).
  • Exhaust System – The exhaust system of a vehicle must be properly secured to the frame of the vehicle a muffler is strongly recommended. Straight Pipe on N/A Cars sounds terrible and some people actually value their hearing.
  • Safety Equipment / Clothes Full Length Pants, a Sleeved T-shirt and Closed toed shoes are required by any Driver or Passenger.
  • Helmet –  A Snell rated helmet is required. DOT only approval is not enough. Helmet must be in good condition no cracks or damaged. Loaner helmets are not available.
  • Seatbelts / Harnesses – Seatbelts must be properly attached and in good working order. If present, aftermarket racing harness all points must be attached to the chassis by methods approved by manufacturer, and must meet racing use requirements.
  • Roll Bar (Convertibles / Open Topped vehicles) – All convertibles / open top / soft top cars must have roll bars equal or exceeding 4 points and be connected to the unibody or sub frame.
  • Tow Hooks – Tow hooks must be present on at least one location on the vehicle.
  • Loose Items – Any loose items in the vehicle including floor mats or aftermarket audio systems must be removed. (A professional install properly secured can pass at inspectors judgement.)

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s